• Locinox Products Locinox Products
  • Gate Automation Gate Automation
  • Sliding Gate Components Sliding Gate Components
  • Swing Gate Components Swing Gate Components
  • Post Components Post Components
  • Fence Components Fence Components
  • Rural Fencing Components Rural Fencing Components
  • Pool Compliant Hardware Pool Compliant Hardware
  • Access Controls Access Controls
  • Accessories & Tools Accessories & Tools
  • Stainless Steel Products Stainless Steel Products
  • Bulk Buy Bulk Buy
  • Clearance
  • Fencing Components
  • Gatemaster Gatemaster
FK555
VERA Digital Wireless Access Control Single side for Insert Locks 40mm Silver

VERA Digital Wireless Access Control for Insert Locks 40mm

The VERA uses advances in battery technology to operate without cables or electricians. The durable battery pack with six lithium metal batteries can withstand extreme weather and allows the VERA to open and close the gate at least 150,000 times. 

Add access control to pedestrian gates easily with VERA, a battery-powered code lock for gates with insert locks (FORTY-, FIFTY-, SIXTY- or EIGHTYLOCK). Easily select, change or delete up to 100 PIN codes. Various entry and exit codes, permanently open codes and free exit are possible. The energy-efficient VERA achieves up to 150,000 open/close cycles with one battery pack, in all weather conditions (IP66). The maintenance-free code lock features aluminium housing and an LED-illuminated electronic code keypad.

  • Double-sided keypad or single-sided keypad (free exit) with cover plate
  • No mains power required. Battery pack (with a lifespan of up to 150,000 cycles) included
  • Weatherproof and LED-illuminated electronic code keypad
  • Easy installation and configuration
  • Easy programming of up to 100 user codes
  • Supports codes for permanently open and free exit
  • Highly robust and vandal-resistant design
  • Aluminium housing with textured paint (black) or anodisation (silver)
  • IP66 rated
  • Compatible with the SFKU-V keep
  • Compatible with FORTY-, FIFTY-, SIXTY- or EIGHTYLOCK (lock not included)


Installation Guide

535.00 535.0 AUD
BKKC132E
Tigerclamp 132 E60 Railing Base Flange series, fit 50NB pipe (60mm OD)

The TigerClamp 132 E60 Series Base Foot Flange is a reliable and robust pipe fitting designed to provide a secure base for 50NB pipes with a diameter of 60mm. This base foot flange is used to attach and support pipes, ensuring stability and structural integrity in various applications. It features a durable construction and is suitable for both indoor and outdoor use. The flange is easy to install and offers a secure connection for your pipe system. With its high-quality design and functionality, the TigerClamp Base Foot Flange is an essential component for any pipe installation project.

39.60 39.6 AUD
WH176
Top Guide Roller for Sliding gate size 40x150mm M18 Black

The Wh176 Top Guide Roller for Sliding Gate is a reliable accessory designed to enhance the performance of sliding gates. With a size of 40x150mm, this guide roller ensures smooth and effortless operation for your gate. It is made of high-quality materials for durability and longevity. The Wh375 Guide Roller is specifically designed to be installed on top posts, providing effective guidance and support. The black color adds a sleek and modern touch to your gate. Upgrade your sliding gate with this top guide roller for improved functionality and convenience.

14.50 14.5 AUD
WH171
Top Guide Roller for Sliding gate size 40x100mm M18 Black

The Wh370 Top Guide Roller for Sliding Gate is a high-quality accessory designed to enhance the performance of sliding gates. With a size of 40x100mm, this guide roller ensures smooth and effortless operation for your gate. It is made of durable materials to withstand daily use and environmental conditions. The Wh370 Guide Roller is specifically designed to be installed on top posts, providing reliable guidance and support. The black color adds a sleek and modern touch to your gate. Upgrade your sliding gate with this top guide roller for improved functionality and convenience.

10.95 10.950000000000001 AUD
GM820
Genuine Beninca 4 button Remote TO.GO4A

Features:

  • Transmitter Frequency: 433 MHz
  • Battery: 23A 12V
  • Coding Type: Rolling
  • Control up to 4 doors 
Battery Type: 23A
Battery Access Type: Tool Required
AS62368.1 Compliant: Not applicable
Battery Included: Yes
Contains Coin Battery: No


44.00 44.0 AUD
ET365
Centsys Photon Smart Fully wireless PE Safety Beams

Centsys Photon Smart Fully wireless PE Safety Beams

Main features:

  • Connects wirelessly to your SMART solution – saves time and money
  • Pair and align in seconds
  • Beautifully styled – adds an air of sophistication to your swing or sliding gate
  • Outstanding reliability offering up to 2 years of battery life
  • Long range – brings safety to even the widest entrance gates
  • Fully sealed unit – prevents insect ingress
  • Can be easily added to sites with existing hard-wired beam sets

Technical Specifications:
Power supply 2 x AA Alkaline Batteries1 (supplied for each transmitter and receiver)
Battery life >2 years
Battery-low indication Notified via MyCentsys Pro Mobile Application
Maximum operating distance 30m
Alignment between beams2 Automatic – 1m circle @ 10m
Maximum Operating Distance Photon SMΔRT Receiver to SMΔRT Controller 10m
Operating temperature -15°C to +65°C
Operating humidity 0 - 90° (non-condensing)
Housing material ABS
Lens material PC
Degree of Protection IP54
Packaging weight 200g
Packaging dimensions Length: 137mm Width: 72mm Height: 58mm


Brochure Click

Installation  Click

189.50 189.5 AUD
LKBL080
Gatemaster Super Digital Lock Double Sided Keypad to fit 10-30 mm gate frame with Lever handle

The Gatemaster Super Lock is a double-sided keypad designed to fit 10-30mm gate frames. With its durable construction and user-friendly keypad, this lock provides enhanced security and convenient access control for your gate. The double-sided keypad allows authorized individuals to enter a personal code for easy and controlled entry.

Download PDF

498.40 498.40000000000003 AUD
GM605
Universal RX Multi Receiver

Description

Introducing the GM605

Product Introduction
  • Name: Universal Radio Receiver 433-868 MHz for Came, Liftmaster,Hormann HSM, Marantec
  • Brand selector: With 8 dip switches user can make different combination for different remote brands.
  • It can worrk with many main different brands in the market, like FAAC, BFT, DITEC, CAME, HORMMAN, BENINCA, MHOUSE, NICE….
  • Multi frequency: 300-868mhz
  •  Learn Button and LED: There are 2 independent channels. Each channel has independent learn button S1, S2 and L1, L2.
  • Power Input Selector: This receiver can work at AC/DC 12V~30V. However, it’s better to change the PIS according to the power input.
  • If the input is great than 24V, shorten pin 2&3; shorten 1&2 if input less than 24V
  • Distance: 50-100 meters
  • Very mini size: 5.5cm*4.5cm*1.0cm
  • One receiver can work with 400 codes
  • It don’t interference other remotes and receivers
  • Compatible brands: nice flors, Marantec 433.92mhz, FAAC SLH rolling code 433.92mhz and 868mhz, liftmaster 310, 390, 433.92mhz, 315mhz, Hormann and Marantec, Berner 868mhz, Prastel, Clemsa Mastercode 433.92mhz, DITEC 433 and 315mhz, V2, Aprimatic, JCM GO 868MHZ, JCM TECH, PNC, FORSA, ALMA, ROPER 868MHZ, BFT, FACC… and many other main brands in the market
  • Programming a new remote 1) First, select the correct brand for remote that will be entry (by dip switch) 2) Press the learning button 1 or 2, the corresponding LED turns on 3) Press the button on the remote, the led 1 or led 2 flashes4 times, the remote button is learned successfully
  • 2 independent relays
  • Delete code:
  • Press and hold either learn button. The LED will start flash. Keep this button pressed, until the LED will turn off. All saved data in the memory card will be erased permanently and can not be recovered


65.00 65.0 AUD
MOT375
Beninca Double Swing Gate Motor TOM5024E Motor Kit

Beninca Double Swing Gate Motor TOM5024E Motor Kit

The TOM series of motors is made by Italian company Beninca which translates into quality, reliability and performance. The TOM range uses linear shaft technology for added length and strength and 24 volt DC motors.

24 VOLT ELECTRIC GATE OPERATOR – RESIDENTIAL & COMMERCIAL –5.0 METRE LEAF

The powerful 24 volt swing gate electro mechanical operator. What makes TOM so special (and yes a little more expensive than most) is just below the top shaft cover. Easily accessible and adjustable mechanical stops. That along with ability to wire encoders makes the TOM highly adaptable to difficult sites where physical stops may be a problem to install. The TOM is a non reversible operator with key operated manual override but one of the main benefits of the 24 volt motor is the ability to use battery backup meaning you may never have to use the manual override key.

Reliable and innovative gear motor, thanks to the 2 adjustable mechanical stops in opening and closing accessible from above and positioned under the metal cover of the shaft. Ideal for the automation of any type of swing gate thanks also to the compact footprints (only 96 mm width) and screw-in brackets. The 45° inclination of the wiring cable allows the distance from the ground to be reduced to a minimum. The rear and front brackets, aligned on the same axis, enable the better distribution of loads by optimizing the lifespan of the actuator. The worm screw protected by wiper ring and stainless steel shaft make it suitable for dusty or sandy environments, or places with aggressive weather conditions

It is possible to use a variety of control boards to control the TOM but the factory designed board is the BRAINY which can be used as a one or two motor controller with a host of programmable parameters.

•At just 96 cm wide, the TOM telescopic linear motor for swing gates to 5 metres long.

•TOM features adjustable mechanical stops for opening and closing, patented FACE gears and a bronze release wheel with customised key.

•The 24 Vdc version, also guarantees standby power consumption of less than 0.8 W.

HIGH-QUALITY COMPONENTS
The release wheel is made of bronze to maximise its life, reliability, and operation. The worm gear is protected by a wiper seal and a stainless-steel shaft, making it suitable for use in dusty, sandy or harsh environments.

COMPACT DESIGN
Thanks to its compact dimensions, just 96 mm wide, TOM adapts to any situation. The 45° inclination of the cable also means that the operator can be installed flush with the floor.

EASY ACCESS TO MECHANICAL STOPS
The adjustable stops at the top are accessible once the metal cover has been slid back. These stops slide on rails and can be easily fixed in the desired position using screws.

FASTENERS DESIGNED FOR MAXIMUM ADAPTABILITY
The rear articulation, which can be fixed in three positions, reduces space requirements by adjusting for any misalignment of the panel during movement. The alignment of the front and rear brackets also ensures better load distribution by reducing bending, guaranteeing axial thrust and optimising operator life.

Additional information

Weight 9.4 kg
Motor Voltage

24 volts DC

Standby Current

0mA

Maximum Current

5.5A

Motor Power

89W

Maximum Thrust

1500Nm

Opening Time

19"

Maximum Gate Width

5000mm

Duty Cycle

80%

Height (mm)

114mm

Width (mm)

96mm

Length (mm)

1575mm

Weight (kg)

9.4 Kg

IP Rating

IP44

 

1,795.00 1795.0 AUD
MOT374
Beninca Single Swing Gate Motor TOM5024E Motor Kit

Beninca Single Swing Gate Motor TOM5024E Motor Kit

The TOM series of motors is made by Italian company Beninca which translates into quality, reliability and performance. The TOM range uses linear shaft technology for added length and strength and 24 volt DC motors.

24 VOLT ELECTRIC GATE OPERATOR – RESIDENTIAL & COMMERCIAL –5.0 METRE LEAF

The powerful 24 volt swing gate electro mechanical operator. What makes TOM so special (and yes a little more expensive than most) is just below the top shaft cover. Easily accessible and adjustable mechanical stops. That along with ability to wire encoders makes the TOM highly adaptable to difficult sites where physical stops may be a problem to install. The TOM is a non reversible operator with key operated manual override but one of the main benefits of the 24 volt motor is the ability to use battery backup meaning you may never have to use the manual override key.

Reliable and innovative gear motor, thanks to the 2 adjustable mechanical stops in opening and closing accessible from above and positioned under the metal cover of the shaft. Ideal for the automation of any type of swing gate thanks also to the compact footprints (only 96 mm width) and screw-in brackets. The 45° inclination of the wiring cable allows the distance from the ground to be reduced to a minimum. The rear and front brackets, aligned on the same axis, enable the better distribution of loads by optimizing the lifespan of the actuator. The worm screw protected by wiper ring and stainless steel shaft make it suitable for dusty or sandy environments, or places with aggressive weather conditions

It is possible to use a variety of control boards to control the TOM but the factory designed board is the BRAINY which can be used as a one or two motor controller with a host of programmable parameters.

•At just 96 cm wide, the TOM telescopic linear motor for swing gates to 5 metres long.

•TOM features adjustable mechanical stops for opening and closing, patented FACE gears and a bronze release wheel with customised key.

•The 24 Vdc version, also guarantees standby power consumption of less than 0.8 W.

HIGH-QUALITY COMPONENTS
The release wheel is made of bronze to maximise its life, reliability, and operation. The worm gear is protected by a wiper seal and a stainless-steel shaft, making it suitable for use in dusty, sandy or harsh environments.

COMPACT DESIGN
Thanks to its compact dimensions, just 96 mm wide, TOM adapts to any situation. The 45° inclination of the cable also means that the operator can be installed flush with the floor.

EASY ACCESS TO MECHANICAL STOPS
The adjustable stops at the top are accessible once the metal cover has been slid back. These stops slide on rails and can be easily fixed in the desired position using screws.

FASTENERS DESIGNED FOR MAXIMUM ADAPTABILITY
The rear articulation, which can be fixed in three positions, reduces space requirements by adjusting for any misalignment of the panel during movement. The alignment of the front and rear brackets also ensures better load distribution by reducing bending, guaranteeing axial thrust and optimising operator life.

Additional information

Weight 9.4 kg
Motor Voltage

24 volts DC

Standby Current

0mA

Maximum Current

5.5A

Motor Power

89W

Maximum Thrust

1500Nm

Opening Time

19"

Maximum Gate Width

5000mm

Duty Cycle

80%

Height (mm)

114mm

Width (mm)

96mm

Length (mm)

1575mm

Weight (kg)

9.4 Kg

IP Rating

IP44


1,395.00 1395.0 AUD
MOT372
Beninca Double Swing Gate Motor TOM3024E Motor Kit

Beninca Double Swing Gate Motor TOM3024E Motor Kit

The TOM series of motors is made by Italian company Beninca which translates into quality, reliability and performance. The TOM range uses linear shaft technology for added length and strength and 24 volt DC motors.

24 VOLT ELECTRIC GATE OPERATOR – RESIDENTIAL & COMMERCIAL – 3.0 METRE LEAF

The powerful 24 volt swing gate electro mechanical operator. What makes TOM so special (and yes a little more expensive than most) is just below the top shaft cover. Easily accessible and adjustable mechanical stops. That along with ability to wire encoders makes the TOM highly adaptable to difficult sites where physical stops may be a problem to install. The TOM is a non reversible operator with key operated manual override but one of the main benefits of the 24 volt motor is the ability to use battery backup meaning you may never have to use the manual override key.

Reliable and innovative gear motor, thanks to the 2 adjustable mechanical stops in opening and closing accessible from above and positioned under the metal cover of the shaft. Ideal for the automation of any type of swing gate thanks also to the compact footprints (only 96 mm width) and screw-in brackets. The 45° inclination of the wiring cable allows the distance from the ground to be reduced to a minimum. The rear and front brackets, aligned on the same axis, enable the better distribution of loads by optimizing the lifespan of the actuator. The worm screw protected by wiper ring and stainless steel shaft make it suitable for dusty or sandy environments, or places with aggressive weather conditions

It is possible to use a variety of control boards to control the TOM but the factory designed board is the BRAINY which can be used as a one or two motor controller with a host of programmable parameters.

•At just 96 cm wide, the TOM telescopic linear motor for swing gates to 3 metres long.

•TOM features adjustable mechanical stops for opening and closing, patented FACE gears and a bronze release wheel with customised key.

•The 24 Vdc version, also guarantees standby power consumption of less than 0.8 W.

HIGH-QUALITY COMPONENTS
The release wheel is made of bronze to maximise its life, reliability, and operation. The worm gear is protected by a wiper seal and a stainless-steel shaft, making it suitable for use in dusty, sandy or harsh environments.

COMPACT DESIGN
Thanks to its compact dimensions, just 96 mm wide, TOM adapts to any situation. The 45° inclination of the cable also means that the operator can be installed flush with the floor.

EASY ACCESS TO MECHANICAL STOPS
The adjustable stops at the top are accessible once the metal cover has been slid back. These stops slide on rails and can be easily fixed in the desired position using screws.

FASTENERS DESIGNED FOR MAXIMUM ADAPTABILITY
The rear articulation, which can be fixed in three positions, reduces space requirements by adjusting for any misalignment of the panel during movement. The alignment of the front and rear brackets also ensures better load distribution by reducing bending, guaranteeing axial thrust and optimising operator life.

Additional information

Weight 10 kg
Motor Voltage

24 volts DC

Standby Current

0mA

Maximum Current

5.5A

Motor Power

89W

Maximum Thrust

1800Nm

Opening Time

9-21 seconds to 90 degrees

Maximum Gate Width

3000mm

Duty Cycle

80%

Height (mm)

132mm

Width (mm)

88mm

Length (mm)

796mm

Weight (kg)

8.2 Kg

IP Rating

IP44


1,539.00 1539.0 AUD
MOT371
Beninca Single Swing Gate Motor TOM3024E Motor Kit

Beninca Single Swing Gate Motor TOM3024E Motor Kit

The TOM series of motors is made by Italian company Beninca which translates into quality, reliability and performance. The TOM range uses linear shaft technology for added length and strength and 24 volt DC motors.

24 VOLT ELECTRIC GATE OPERATOR – RESIDENTIAL & COMMERCIAL – 3.0 METRE LEAF

The powerful 24 volt swing gate electro mechanical operator. What makes TOM so special (and yes a little more expensive than most) is just below the top shaft cover. Easily accessible and adjustable mechanical stops. That along with ability to wire encoders makes the TOM highly adaptable to difficult sites where physical stops may be a problem to install. The TOM is a non reversible operator with key operated manual override but one of the main benefits of the 24 volt motor is the ability to use battery backup meaning you may never have to use the manual override key.

Reliable and innovative gear motor, thanks to the 2 adjustable mechanical stops in opening and closing accessible from above and positioned under the metal cover of the shaft. Ideal for the automation of any type of swing gate thanks also to the compact footprints (only 96 mm width) and screw-in brackets. The 45° inclination of the wiring cable allows the distance from the ground to be reduced to a minimum. The rear and front brackets, aligned on the same axis, enable the better distribution of loads by optimizing the lifespan of the actuator. The worm screw protected by wiper ring and stainless steel shaft make it suitable for dusty or sandy environments, or places with aggressive weather conditions

It is possible to use a variety of control boards to control the TOM but the factory designed board is the BRAINY which can be used as a one or two motor controller with a host of programmable parameters.

•At just 96 cm wide, the TOM telescopic linear motor for swing gates to 3 metres long.

•TOM features adjustable mechanical stops for opening and closing, patented FACE gears and a bronze release wheel with customised key.

•The 24 Vdc version, also guarantees standby power consumption of less than 0.8 W.

HIGH-QUALITY COMPONENTS
The release wheel is made of bronze to maximise its life, reliability, and operation. The worm gear is protected by a wiper seal and a stainless-steel shaft, making it suitable for use in dusty, sandy or harsh environments.

COMPACT DESIGN
Thanks to its compact dimensions, just 96 mm wide, TOM adapts to any situation. The 45° inclination of the cable also means that the operator can be installed flush with the floor.

EASY ACCESS TO MECHANICAL STOPS
The adjustable stops at the top are accessible once the metal cover has been slid back. These stops slide on rails and can be easily fixed in the desired position using screws.

FASTENERS DESIGNED FOR MAXIMUM ADAPTABILITY
The rear articulation, which can be fixed in three positions, reduces space requirements by adjusting for any misalignment of the panel during movement. The alignment of the front and rear brackets also ensures better load distribution by reducing bending, guaranteeing axial thrust and optimising operator life.

Additional information

Weight 10 kg
Motor Voltage

24 volts DC

Standby Current

0mA

Maximum Current

5.5A

Motor Power

89W

Maximum Thrust

1800Nm

Opening Time

9-21 seconds to 90 degrees

Maximum Gate Width

3000mm

Duty Cycle

80%

Height (mm)

132mm

Width (mm)

88mm

Length (mm)

796mm

Weight (kg)

8.2 Kg

IP Rating

IP44


1,095.00 1095.0 AUD
GMSG706
Beninca BULL624 SW 24V 600kg- Motor Kit

Italian Sliding Gate Motor Beninca BULL424 SW 24V 600kg- Motor kit

 

The BULL624SW is a 24 volt motor designed for residential and commercial sliding gates up to 600kg in weight. 24 VOLT ELECTRIC GATE OPERATOR - RESIDENTIAL - 600KG The BULL624SW by Beninca is plain and simple Beninca quality and reliability throughout. The BULL424SW is designed for residential and commercial sliding automatic gates up to 600kg in weight.

24 Vdc gear motor for intensive use with integrated control unit and virtual encoder | Switching power supply 240 Vac which reduces energy consumption and ensures a long lifespan of the actuator | Control unit with trimmers and dip-switches | The virtual encoder enables optimal management of slowing-down phases, movement tracking (STC system) and torque management in relation to the position of the gate, guaranteeing maximum safety | Operation guaranteed even in the event of a power supply failure through batteries that can be perfectly integrated in the motor (2 x 1.2 Ah) | Anti-crushing system with amperometric obstacle detection.

The BULL624SW has a built in control board in its own seperate enclosure with a dedicated 433mhz wireless receiver and inputs for photocells and switches etc. The BULL also comes with a base plate. Battery backup is optional with the addition of the battery module and two 1.3Ah rechargeable batteries.

 Motor Voltage - 24 volts DC 

Current Standby - 8mA 

Current at use - 3.2A 

Motor power - 80W 

Maximum thrust - 428N 

Operating speed - 11 metres per minute (adjustable) 

Maximum gate size - 600 kg 

Duty cycle - 80% 

Height - 330mm Width - 326mm Depth - 140mm 

Weight - 7.6 Kg 

IP rating - IP44

 

 

Additional information

Weight 15 kg
Motor Voltage

24 volts DC

Standby Current

8mA

Maximum Current

0.4A

Motor Power

80W

Maximum Thrust

428N

Operating Speed

11 Metres per minute

Maximum Gate Weight

600 Kg

IP Rating

IP44

Height (mm)

330mm

Width (mm)

140mm

Length (mm)

326mm

Weight (kg)

10.2 Kg

Duty Cycle

80%

 

799.00 799.0 AUD
GMSG702
Beninca BULL424 SW 24V 450kg- Motor Kit

Italian Sliding Gate Motor Beninca BULL424 SW 24V 450kg- Motor kit

 

The BULL424SW is a 24 volt motor designed for residential and commercial sliding gates up to 450kg in weight. 24 VOLT ELECTRIC GATE OPERATOR - RESIDENTIAL - 450KG The BULL424SW by Beninca is plain and simple Beninca quality and reliability throughout. The BULL424SW is designed for residential and commercial sliding automatic gates up to 450kg in weight.

24 Vdc gear motor for intensive use with integrated control unit and virtual encoder | Switching power supply 240 Vac which reduces energy consumption and ensures a long lifespan of the actuator | Control unit with trimmers and dip-switches | The virtual encoder enables optimal management of slowing-down phases, movement tracking (STC system) and torque management in relation to the position of the gate, guaranteeing maximum safety | Operation guaranteed even in the event of a power supply failure through batteries that can be perfectly integrated in the motor (2 x 1.2 Ah) | Anti-crushing system with amperometric obstacle detection.

The BULL424SW has a built in control board in its own seperate enclosure with a dedicated 433mhz wireless receiver and inputs for photocells and switches etc. The BULL also comes with a base plate. Battery backup is optional with the addition of the battery module and two 1.3Ah rechargeable batteries.

 Motor Voltage - 24 volts DC 

Current Standby - 8mA 

Current at use - 3.2A 

Motor power - 80W 

Maximum thrust - 428N 

Operating speed - 11 metres per minute (adjustable) 

Maximum gate size - 450 kg 

Duty cycle - 80% 

Height - 330mm Width - 326mm Depth - 140mm 

Weight - 7.6 Kg 

IP rating - IP44


 

Additional information

Weight 15 kg
Motor Voltage

24 volts DC

Standby Current

8mA

Maximum Current

0.4A

Motor Power

80W

Maximum Thrust

428N

Operating Speed

11 Metres per minute

Maximum Gate Weight

400 Kg

IP Rating

IP44

Height (mm)

330mm

Width (mm)

140mm

Length (mm)

326mm

Weight (kg)

10.2 Kg

Duty Cycle

80%

 

690.00 690.0 AUD
CP858
Sunbury - Aluminium Capital 150x150mm

Sunbury Aluminium Capital - 125x125

The Sunbury Aluminium Capital is a stunning architectural element designed to enhance the beauty of columns and pillars. Made from high-quality aluminum, this capital showcases a unique and eye-catching design that adds a touch of elegance to any architectural project. With its intricate detailing and precise craftsmanship, the Sunbury Aluminium Capital creates a focal point that captures attention and elevates the visual appeal of the space. Whether used in residential or commercial applications, this capital is built to withstand the test of time, ensuring durability and long-lasting performance. Transform your columns and pillars into works of art with the Sunbury Aluminium Capital.

115.00 115.0 AUD
HN724
Safetech AlfaHinge Neutral Tension Hinge for Gates up to 28kg: Black, No Legs

The Neutral Tension Gate Hinge is designed for gates weighing up to 28kg and features a no alignment leg design.  The absence of alignment legs simplifies the installation process and allows for flexible positioning. With its durable construction, the Neutral Tension Gate Hinge offers long-lasting performance. Whether for residential or light commercial use, this hinge is an excellent choice for smaller gates.


Hold weights up to 28kg

Materials

Engineered Polymers, Rust Resistang Stainless-Steel Pins & Springs

Adjustment

Vertical

Colour

Black

Max Holding Weight (KG)

28

Number of Legs

No Legs

Application

Metal or Timber Gates, Pool Gates

14.99 14.99 AUD
HGSK251
Swing Gate hinges Shackle Weld on Hinges 20mm pin in Dark Grey (Pair)

The Swing Gate Hinges Shackle Weld-on Hinges are heavy-duty hinges designed for swing gates that require strength and reliability. With a 20mm pin size, these hinges offer robust performance and smooth gate operation. The shackle design helps prevent gate sagging and ensures proper alignment. These hinges are sold as a pair and feature a weld-on installation for secure and permanent attachment. Suitable for industrial and commercial applications, the Swing Gate Hinges Shackle Weld-on Hinges provide long-lasting durability and reliable gate functionality.


Colour: Dark Grey

Hold weights up to 600kg


Installation instruction for Weld on hinges

  1. Weld the sockets onto the gate itself.
  2. Measure the distance between the sockets.
  3. Weld the pins onto your post, one at the bottom, and one at the top. Make sure you have left plenty of room at the bottom so the gate clears the ground. Double check the pins are the same distance apart as your sockets. The pins should be pointing up.
  4. Lift your gate up and drop it on the pins.

To make sure your gate is secure :

  1. Weld the bottom pin onto your post & pin pointing up and your bottom socket on your gate.
  2. Sit your gate on the bottom pin.
  3. Weld the top socket to your gate.
  4. Drop the pin into the top socket. so Pin is pointing down
  5. Weld the pin to the post.

Tip: Measure correctly before welding. If need to change anything you will need to cut them off and re-weld them again.


25.85 25.85 AUD
HGHA298
Heavy duty Adjustable weld on Swing Gate Hinge 20mm pin with Nuts- pair

The Swing Gate Hinge Adjustable is a high-quality hinge designed for swing gates. It features a 20mm pin with a rotating mechanism, allowing for easy adjustment and precise alignment of the gate. The pair of hinges ensures stability and smooth operation of the gate. Crafted with durability in mind, this hinge is built to withstand outdoor conditions. Upgrade your swing gate with the Swing Gate Hinge Adjustable for enhanced functionality and convenience.


Hold weights up to 150kg

34.50 34.5 AUD
LKBL077
Gatemaster Super Digital Lock Double Sided Keypad to fit 40-60mm gate frame with Lever handle

The Gatemaster Super Lock is a double-sided keypad designed to fit 40-60mm gate frames. With its durable construction and user-friendly keypad, this lock provides enhanced security and convenient access control for your gate. The double-sided keypad allows authorized individuals to enter a personal code for easy and controlled entry.

Download PDF

498.40 498.40000000000003 AUD
WH195
Top Guide Roller for Sliding gate size 200x40mm with holding bracket

The WH195 Top Guide Roller for Sliding Gate is a reliable and functional accessory designed to improve the performance of sliding gates. With a size of 200x40mm and a sturdy holding bracket, this guide roller ensures smooth and effortless operation for your gate. It is constructed with high-quality materials to ensure durability and long-lasting performance. The WH190 Guide Roller is specifically designed to provide reliable guidance and support for sliding gates. The holding bracket adds extra stability and security to the installation. Upgrade your sliding gate system with this top guide roller for optimal functionality.

27.50 27.5 AUD